Items with > before the name is a folder that when selected shows another level of customization. See the Model Match page for more info about Model Matching. The Model Mismatched message will also show up to indicate you are connected to a receiver, but the model selected on your radio is incorrect. When not connected to any receiver, it will show a dash ( -) while a C shows up when bound and connected. The Connection Status indicator shows your current RC link status. This is most dangerous when you're armed and flying several kilometers/miles out, as this could mean a sudden Failsafe. Make sure your module is not overheating and it's still getting a good connection with the radio. Should the indicator starts showing Bad Packets, and Good Packets goes down, it isn't a good situation. Any small fluctuation is normal and often goes back to 100% Good Packets, especially when you change a setting and it's committed into memory. If you've set your Packet Rate to 500Hz, the Packet Counter should show 0/500, which means you're not getting any Bad Packets ( 0 Bad Packets ) and only getting Good Packets ( 500 Good Packets ). The second set of numbers should match your currently selected Packet Rate. The first part will show you the current ExpressLRS TX Module ID, followed by the current status of the link. The first line, "Header", will show you some information about your ExpressLRS link. This could result in a desync on some hardware combination which would result in a FAILSAFE. When a parameter is changed, the module goes into Parameter Commit mode, interrupting the normal loop. If you're on a Released version or a Release Candidate, this will read something like 3.0 or 3.0-RC1 plus the commit hash of the release.ĭo not change parameters while ARMED. In the first photo above, master means the module is flashed with the Master Branch with the git commit 942c40. You can reference this hash from Releases. The master 942c40 from the photo above is the git branch and commit hash of the firmware version that the module has. If the Bad/Good indicates something other than 0/ this means CRSFshot is not working- verify that you properly followed the Radio Preparation Guide. If parameters do show up, but the Bad/Good section on the right side of the header is showing an unstable value, have a look at your model settings and make sure the Internal RF module is set to Off. Another possible reason is that you haven't updated the firmware of the module to version 2.x. If there is no LED lit up, it is possible the Protocol set for the External Module is incorrect (should be set to CRSF) or that the module is not properly connected to the pins of the JR bay of the radio. If the parameter list does not populate after a few seconds, and it's stuck at Loading., first verify the ExpressLRS module has power by checking its LED. Here's how it looks in the Tools menu (X9D+ and T16 Shown):Įnter the Lua script by selecting "ExpressLRS" in the Tools menu and pressing ENTER. Now that you have flashed your TX it is time to learn how to use the ELRS Lua script! Installing the Lua Script ¶ĭownload the ELRSv3 Lua Script (you can simply right-click, save-as) into your radio's SD Card under the Scripts/Tools folder and Long Press the "SYS" button (for T16 or similar Radios) or the "Menu" button (for Taranis X9D or similar Radios) to access the Tools Menu where you can find the ExpressLRS script ready to run with only one click. Crystal Oscillator (XO) Frequency Error.On v1.x, I can choose 2W on the Lua, but I cannot do that anymore.There is no C on the top right corner, and I'm not getting Telemetry in my radio!.VTX Admin is not working but I can change VTX channels via OSD Menu.I cannot change to Full Resolution Rates!.I cannot change my Packet Rate to F1000!.ExpressLRS Lua Script is stuck at Loading.Using The Lua Script Using The Lua Script Table of contents.Updating Transmitters Updating Transmitters.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |